The default maximum I-frame size is 1472. (Optional) Host link to be used for the focal point support. (Optional) Delay (in seconds) between attempts to retry establishing connection with the remote host PU. The range is from 0 to 255 (0 = no retry attempts, 255 = infinite retry attempts). (Optional) Number of times the SNA Service Point attempts to retry establishing connection with the remote host PU. (Optional) Send and receive maximum I-frame sizes used for the host link. (Optional) Send and receive window sizes used for the host link. (Optional) Slot and port number of the interface. (Optional) local SAP (LSAP) address used by the SNA Service Point to establish connection with the remote host. (Optional) Service access point (SAP) address of the remote host PU. MAC address of the remote host physical unit (PU). For example, if the XID value is 05D00001, the block number is 05D and the ID number is 00001. The XID value is eight hexadecimal digits that include both block and ID numbers. No sna host host-name xid-snd xid rmac remote-mac Syntax DescriptionĮxchange identification (XID) that will be sent to the host during connection establishment. Sna host host-name xid-snd xid rmac remote-mac To cancel the definition, use the no form of this command. To define a link to a Systems Network Architecture (SNA) host over Token Ring, Ethernet, FDDI, remote source-route bridging (RSRB), or virtual data-link control connections, use the sna host command in global configuration mode. In the following example, SDLC address C1 is enabled for use by host connections: encapsulation sdlcĭefines a link to a Systems Network Architecture (SNA) host over an SDLC connection. Required keyword for SDLC data-link control. No sna enable-host sdlc sdlc-address Syntax Description To enable a Synchronous Data Link Control (SDLC) address for use by host connections, use the sna enable-host command in interface configuration mode. Specifies the X.121 address of the remote X.25 device with which communication is planned using QLLC conversion. In the following example, X.121 subaddress 320108 is enabled for use by host connections: sna enable-host qllc 320108ĭefines a link to an SNA host over an X.25/QLLC connection. No default X.121 subaddress is specified. Required keyword for Qualified Logical Link Control (QLLC) data-link control. No sna enable-host qllc x121-subaddress Syntax Description To disable SNA Service Point on the interface, use the no form of this command. To enable an X.121 subaddress for use by the Systems Network Architecture (SNA) Service Point feature on the interface, use the sna enable-host command in interface configuration mode. Sna host (Token Ring, Ethernet, FDDI, RSRB, VDLC)ĭefines a link to an SNA host over Token Ring, Ethernet, FDDI, remote source-route bridging (RSRB), or virtual data-link control (VDLC) connections. The following example enables SNA on the interface and specifies that the local SAP (LSAP) 10 will be activated as an upstream SAP: sna enable-host lsap 10ĭisplays the status of the SNA Service Point feature.ĭefines a link to an SNA host over a Frame Relay connection. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware. This command is supported in the Cisco IOS Release 12.2SX train. This command was integrated into Cisco IOS Release 12.2(33)SRA. (Optional) Activate a local service access point (SAP) as an upstream SAP, for both receiving ConnectIn attempts and for starting ConnectOut attempts. To disable SNA on the interface, use the no form of this command. To enable Systems Network Architecture (SNA) on the interface, use the sna enable-host command in interface configuration mode. Sna enable-host (Token Ring, Ethernet, Frame Relay, FDDI) sna host (Token Ring, Ethernet, FDDI, RSRB, VDLC).sna enable-host (Token Ring, Ethernet, Frame Relay, FDDI).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |